Sagarpur, New Delhi, Delhi 110046
- 4.5 (186)
- Verified hires
Please fill out the form to contact a specialist
Showing 4 Slab Cutting Services in Sagarpur
Sagarpur, New Delhi, Delhi 110046
Sagarpur West, New Delhi, Delhi 110046
Sagarpur, New Delhi, Delhi – 110046, India.
Sagarpur Main Market, Sagarpur, South West Delhi, Delhi – 110046
Imagine you own a three-storey house in Sagarpur. Your family is growing, and you need a staircase to the top floor, or maybe a lift for your parents. The plan is ready, the mason is ready, but one thing is stopping everything: a thick concrete slab that cannot simply be knocked out.
This is a very common situation in Sagarpur, Dabri, Uttam Nagar and the lanes around them. Houses are tightly packed, floors are stacked on top of each other, and every wall and slab shares load with the next one. A careless cut can spread cracks through the whole building.
A trained slab cutting service in Sagarpur is the safe answer. At Core Cutting India, we cut RCC floor slabs and roof slabs with diamond saws along clean, pre-approved lines. You get the exact opening you need, and the rest of your building stays sound.
📞 Call or WhatsApp: 7009679903 ✉️ Email: info@corecuttingindia.com
A slab is the flat concrete layer that forms a floor or roof. It is reinforced with steel bars and carries the weight of people, furniture and the floors above.
Slab cutting means removing a planned portion of this slab using a machine with a diamond blade. The blade cuts through both concrete and steel in a straight, thin line. The loose block is then lifted out safely.
You may hear it called by other names:
All of them describe the same job: a controlled opening in a concrete slab.
Sagarpur is a dense residential and commercial area in West Delhi. Many buildings have been extended upward over the years. Some were constructed decades ago, and plans were never kept. Neighbouring walls are often shared or very close.
Because of this, slab work here needs extra care:
Machine cutting handles these challenges much better than hammering. It is quieter, more precise, and easier to control.
The cut line follows your marking. Edges are straight, so finishing work like plaster, railing and tiling is simple.
Diamond cutting creates very little vibration. This protects beams, columns and walls that are close to the opening.
Water is used during cutting, which keeps dust under control. The machines are far quieter than breakers.
Many openings are completed in a few hours, so your next stage of work can start sooner.
Because the slab is cut into blocks, there is no shower of broken concrete across the site.
We decide the order of cuts and use supports so that pieces do not fall unexpectedly.
| Type | What It Means |
|---|---|
| Opening cutting | A square or rectangular hole in the slab |
| Strip cutting | Long cuts to remove a section of slab |
| Floor sawing | Straight cuts in ground floors and pavements |
| Edge cutting | Trimming the slab edge for extension work |
| Full removal of a bay | Taking out a larger portion of the slab in stages |
Share your location, slab type (roof or floor), opening size and a couple of photos on WhatsApp or call.
We visit the site to check slab thickness, steel pattern, nearby beams, and how the machine can be placed.
You receive a clear price. If we find anything that may increase the effort, we tell you before starting.
We draw the cutting lines on the slab. You check them and confirm.
We prop the slab where needed, protect the floor below and clear the working area.
Using a slab saw or wire saw, we cut along the lines with continuous water flow.
The cut blocks are lifted or broken down safely, and the slurry is cleaned.
| Machine | Where It Is Used |
|---|---|
| Walk-behind slab saw | Straight cuts on floors and roofs |
| Hand-held ring saw | Corners and edges that large saws cannot reach |
| Wire saw | Very thick slabs or hard-to-reach locations |
| Wall saw | Cuts linked to walls and beams |
| Core drill | Round holes for pipes and cables |
The diamond segments on the blade grind through concrete and steel. That is why the edge is smooth and the cut is controlled.
A slab is a load-bearing part of your building. Cutting it without planning is risky. Here is what we do:
Please note: For large openings or in very old buildings, we recommend consulting a structural engineer. This simple step can save you from major trouble later.
People often search "slab cutting rate per foot" or "slab cutting cost near me". Here is a clear breakdown.
Factors that affect the price:
Indicative rates (for general guidance):
| Work Type | Approximate Range |
|---|---|
| Slab up to 6 inch thick | ₹90–₹150 per running foot |
| Slab 6–10 inch thick | ₹150–₹300 per running foot |
| Thick or heavily reinforced slab | ₹300 and above per running foot |
| Core holes | Per hole, based on diameter and depth |
| Small single-opening jobs | Minimum job charge may apply |
These are starting estimates only. After inspection, we share a final quote.
Check your estimate now: Use our Rate Calculator or message your measurements on WhatsApp at 7009679903.
| Factor | Machine Slab Cutting | Manual Breaking |
|---|---|---|
| Accuracy | High | Low |
| Vibration | Very low | Very high |
| Noise | Lower | Very loud |
| Dust | Controlled | Heavy |
| Edge finish | Smooth | Rough |
| Time | Short | Long |
| Risk to structure | Low | High |
For crowded areas like Sagarpur, machine cutting is the more sensible choice.
We provide slab cutting service in Sagarpur and these nearby areas:
We also offer our service in other cities across India. If you are in another part of Delhi, please check these pages:
You can explore all our services at Core Cutting India.
Slab cutting service in Sagarpur is the professional cutting of RCC floor and roof slabs with diamond machines. It is used to create openings for stairs, lifts, ducts and renovation work without damaging the rest of the building.
Slab cutting usually starts at about ₹90 to ₹150 per running foot for slabs up to 6 inches thick. The final cost depends on thickness, steel, access and total length. Use our rate calculator or call 7009679903 for a quote.
Yes, if it is planned properly. We inspect the slab, use supports where needed and cut in a safe order. For large openings in old buildings, a structural engineer's advice is recommended.
A standard staircase opening is often finished in a few hours. Thicker slabs or larger openings may take one or two days.
No, not when done correctly. Diamond cutting causes very little vibration, so nearby walls, beams and columns stay protected.
Yes. Diamond blades and wire saws cut through concrete and steel reinforcement together to give a clean edge.
Yes. We serve Sagarpur, Dabri, Uttam Nagar, Janakpuri, Vikaspuri, Dwarka, Palam, Najafgarh and nearby areas. Call or WhatsApp 7009679903 to confirm timing.
Call or WhatsApp 7009679903 with your location, slab details and photos. We will arrange an inspection and send you a quote. You can also email info@corecuttingindia.com.
A slab is the backbone of your floor or roof, so the way it is opened matters. A professional slab cutting service in Sagarpur gives you precise openings, low vibration, less dust and a much faster finish than manual breaking. Core Cutting India brings modern diamond equipment, careful planning and honest pricing to every job, whether it is a simple staircase opening or a larger commercial project.
Send us a photo and your measurements today, and we will guide you from there.
Message us on WhatsApp now and get your slab cutting quote the same day.
👉 Can't find your city? Request Slab Cutting Service now
Serving 580+ cities across India with verified professionals.