Renovation is common in Rampur today. Families are adding terrace stairs in Civil Lines, shop owners are opening upper floors near Shahbad Gate, and schools and clinics are planning lifts. Almost every one of these plans needs a hole in a concrete roof or slab.
The old way is to call a labour team with a breaker. The result is often a cracked slab, chipped beams, a lot of dust and unhappy neighbours. A professional roof cutting service in Rampur does the same job with diamond cutting tools, so the opening is clean, the vibration is low and the rest of the building stays safe.
Core Cutting India provides roof, slab, wall and core cutting across Rampur city, Bilaspur, Milak, Swar, Shahabad, Tanda and nearby areas.
Call or WhatsApp 7009679903 to discuss your job and get a clear, no-pressure quote.
Roof Cutting in Rampur
Roof cutting is a method of removing a marked section of an RCC roof or slab with diamond blades, wires or core bits. It is used to create openings for stairs, lifts, ducts, skylights and pipes.
Why it is better than breaking:
- The cut follows your marked line exactly
- Very little shaking reaches the rest of the building
- Noise and dust are lower
- Less patch work is needed afterwards
Signs You Need a Professional Roof Cutting Service
You probably need one if:
- You want to add a staircase to reach the terrace or a new floor
- A lift is planned in an existing home, hospital, hotel or school
- You want a skylight or better ventilation in a closed room
- A plumber, electrician or AC installer needs holes through the slab
- A part of an old slab must be removed during renovation
- A factory or godown needs an opening for machines, ducts or conveyors
In all these cases, precise cutting saves time and prevents damage.
Our Roof Cutting Services in Rampur
RCC Roof and Slab Cutting
We cut reinforced concrete of different thicknesses. The blade and machine are chosen after checking the slab and the steel inside it.
Terrace Staircase Opening
A properly sized opening lets your mason or contractor build stairs without extra chipping or correction.
Lift Pit and Lift Shaft Cutting
We prepare the openings needed for elevator installation with careful control so nearby beams and columns are not disturbed.
Skylight, Duct and Ventilation Cutting
Neat rectangular or round openings for daylight, exhaust fans, chimneys and air ducts.
Wall Saw Cutting
For doors, windows, passages and shear walls. Track-guided saws give straight lines even in thick walls.
Wire Saw Cutting
Best for heavy structures, deep beams, columns and places where a blade cannot fit.
Core Drilling
Round holes for water supply, drainage, electrical cables, AC pipes and fire-safety lines, in slabs and walls.
Controlled Removal of Slab Sections
The cut piece is supported, lifted or broken into blocks in an organised way, so the rest of the building is not affected.
What Makes Our Method Different
| What matters to you |
How we handle it |
| Accuracy |
Lines are marked and approved before any cutting |
| Building safety |
Low-vibration diamond cutting, slab support planning |
| Cleanliness |
Water cooling and slurry control |
| Noise |
Much lower than hammering |
| Timing |
Most small and medium jobs done in one to two days |
| Price clarity |
Rate explained before work starts |
Step-by-Step: How Your Job Will Go
Step 1: Call or WhatsApp. Send your location, cut size and photos to 7009679903.
Step 2: Quick site check. We see the slab, access, water, power and safety needs.
Step 3: Quote and plan. You get a clear price and a simple plan for the work.
Step 4: Marking. Cut lines are marked as per your drawing or engineer's advice and confirmed with you.
Step 5: Safety setup. Barricading, slab support and slurry control are arranged.
Step 6: Diamond cutting. Our operators cut carefully along the lines.
Step 7: Removal and cleaning. The cut section is taken out, the area is cleaned and the opening is ready for the next stage.
Machines and Technology We Use
- Slab saws for horizontal cutting in roofs and floors
- Wall saws for exact vertical and straight cuts
- Wire saws for very thick or complex concrete
- Core drilling machines for round holes of many diameters
- Diamond tools chosen for the concrete grade and steel density
- Water and slurry control to protect the blade and keep work clean
Using the correct machine is what keeps the edges clean and the cost under control.
Safety Practices on Every Site
- Structural opinion is advised for load-bearing slabs and beams
- The cut portion is supported so it cannot drop suddenly
- Workers use helmets, gloves, goggles, ear protection and safety shoes
- Water and electricity are managed with proper earthing
- The area below the roof is cleared of people and valuables
- Slurry and debris are removed to prevent slips and stains
Tell us if your building is old, has heavy loads or has had earlier repairs. We will adjust the plan.
Roof Cutting Cost in Rampur: Simple Pricing Guide
The roof cutting cost in Rampur is not the same for every job. The price mostly depends on:
- Slab thickness
- Total length of the cuts
- Amount of steel bars in the slab
- Type of machine needed
- Height and access to the work area
- Debris shifting requirements
- Distance from our team to your site
Approximate rate ranges (for guidance only):
| Work |
Basis |
Approximate Range |
| RCC roof / slab cutting |
Per running foot |
₹80 to ₹250 |
| Wall saw cutting |
Per running foot |
₹100 to ₹300 |
| Core drilling |
Per hole (by diameter) |
₹300 to ₹2,500 |
| Wire saw cutting |
Per project |
Quoted after inspection |
| Small jobs |
Minimum charge |
On request |
Final price depends on your site conditions.
Try this first: use our Rate Calculator to get a rough budget, then call 7009679903 for the exact figure.
Tips to reduce cost:
- Share exact size and photos before the visit
- Book all cuts together in one visit
- Keep power and water ready
- Make sure the machine can reach the working area
Common Use Cases in Rampur
- Homes: terrace stairs, skylights, extra room openings
- Shops and showrooms: upper floor access, duct and AC openings
- Hospitals and clinics: lift installation, service shafts
- Schools and colleges: stairs, lift openings, pipe passages
- Hotels and banquet halls: ventilation cuts, layout changes
- Godowns, cold stores and sugar-related units: machine and ventilation openings
- Renovation work: removing part of an old slab
Areas We Serve Around Rampur
Rampur City
Civil Lines, Shahbad Gate, Nawab Gate, Ganj, Bilaspur Road, Moradabad Road, Bareilly Road and nearby colonies
Towns and Tehsils
Bilaspur, Milak, Swar, Shahabad, Tanda, Saidnagar, Chamraua, Kemri, Azim Nagar
Nearby Districts
Moradabad, Bareilly, Bijnor, Sambhal, Amroha, Budaun, Nainital, Rudrapur
Other Cities
We also provide cutting services in Delhi NCR, Noida, Ghaziabad, Meerut, Aligarh, Agra, Lucknow, Kanpur, Varanasi and Prayagraj.
Need us in another part of Uttar Pradesh? Visit these pages:
Not sure if we reach your area? Call 7009679903 and we will let you know.
Why Rampur Customers Choose Core Cutting India
- Clear pricing: no confusing extras
- Suitable machine for each job: not one tool for everything
- Skilled operators: people who understand concrete and steel
- Protection of your property: we take care of floors, walls and surroundings
- Team coordination: easy to work with your engineer, architect or contractor
- Simple communication: call, WhatsApp or email
Quick Checklist Before Booking
- Confirm with your engineer if the slab is load-bearing.
- Keep the drawing or a rough sketch ready.
- Send clear photos and measurements.
- Check water and power availability.
- Inform neighbours about the cutting time.
- Ask if debris removal is included.
- Compare methods and not just the lowest price.
Frequently Asked Questions
1. What is the cost of roof cutting service in Rampur?
The cost depends on slab thickness, cutting length, steel density and machine type. RCC roof cutting is usually priced per running foot, and small jobs may have a minimum charge. Use our rate calculator or call 7009679903 for an exact quote.
2. Is roof cutting safe for my house in Rampur?
Yes, when planned well. Diamond cutting causes far less vibration than breaking, so it is safer for both old and new buildings. For load-bearing slabs, please check with a structural engineer first.
3. How long does it take to cut a roof?
A small opening for stairs or a duct often takes a few hours to one day. Thick slabs, dense reinforcement or tricky access may need two days or more.
4. Will cutting damage the remaining roof?
No, not when diamond tools are used. The edges are clean and the surrounding concrete remains intact.
5. Do you serve Bilaspur, Milak and Swar near Rampur?
Yes. We serve Rampur city and nearby towns such as Bilaspur, Milak, Swar, Shahabad and Tanda. Call us to confirm your exact location.
6. What is the difference between roof cutting and slab cutting?
Roof cutting refers to cutting the top slab of a building. Slab cutting is a broader term for any concrete floor or roof slab. Both use the same diamond cutting methods.
7. Do you also provide wall cutting and core drilling in Rampur?
Yes. Along with roof cutting, we offer wall saw cutting, wire saw cutting and core drilling for pipes, cables, ducts and openings.
8. How can I book roof cutting service in Rampur?
Call or WhatsApp 7009679903, or email [email protected] with your location, cut size and photos. We will arrange a site check and share a clear quote.
Conclusion: Get Reliable Roof Cutting Service in Rampur
Changing a roof or slab is a big decision, and it should be done with the right tools and the right care. Whether you are adding stairs, installing a lift, opening a skylight or making space for pipes and ducts, a professional roof cutting service in Rampur gives you cleaner results, safer work and lower repair costs.
Core Cutting India brings diamond cutting technology, careful planning and honest communication to every job, across Rampur city, Bilaspur, Milak, Swar, Shahabad, Tanda and the wider region.
Contact us today:
Send your location, cut size and a few photos on WhatsApp, and get a quick quote for roof cutting service in Rampur.
