Think of core cutting as a small logistics project. A machine weighing several kilograms has to reach the right wall, at the right time, with the right power and water, while a clear plan guides the crew. When one piece is missing, the whole visit stalls.
Most guides on this subject list tips. This one gives you a countdown plan: what to do a week before, three days before, the day before and on the day itself. Along the way it covers the four areas that matter most for smooth work: measurements, utilities, machine access and overall site readiness. It is written for homeowners, shopkeepers, builders and facility managers across Punjab, and it can be used as a printable schedule.
Want your core cutting job planned properly? Call or WhatsApp 7009679903 and share your photos and measurements for a fast, clear quote. Email: info@corecuttingindia.com
The Four Pillars of a Well-Planned Core Cutting Job
Before the timeline, a quick summary of what each pillar covers.
- Measurements: hole diameter, depth, thickness, position and spacing.
- Utilities: electricity, water and, where relevant, lighting and ventilation.
- Machine access: how equipment and people reach the cutting point.
- Site readiness: clearance, protection, permissions and safety.
Think of them as four legs of a table. If one is short, the job wobbles.
T-7 Days: Get Your Measurements Right
A week before the job is the best time to measure, because you still have room to adjust the plan.
What to measure
- Hole diameter. Match it to the pipe, duct or cable, adding space for sleeves, insulation or sealing material. Ask your plumber or AC technician what size they need.
- Wall or slab thickness. Measure at an existing opening, or ask the contractor how to estimate it. Include plaster, tiles and screed.
- Position. Measure from fixed points such as corners, door frames or columns. Record both horizontal and vertical distances.
- Spacing. If there are several holes, measure the distance between them and to the nearest edge, beam or column.
- Height from floor. For wall holes, note the height of the centre point. This matters for drainage slopes and AC line routing.
- Clearance on the other side. Check what is behind the wall or below the slab: a cupboard, bed, kitchen counter or false ceiling.
Record it neatly
Create a simple table with columns for location, purpose, diameter, thickness and notes. Add photos of each marked point. This table becomes the basis of your quote and your instructions to the crew.
If you want help turning measurements into a cost estimate, use our core cutting rate calculator.
Check the structure
At this stage, also ask whether any hole is close to a beam, column or load-bearing wall. If so, involve a structural engineer. Our checklist on important checks before making openings in concrete slabs explains the main risks.
T-5 Days: Plan Your Utilities
Utilities are where many jobs fail, so give them their own planning slot.
Electricity
- Ask your contractor for the machine's power rating. Many compact rigs run on single-phase 220 to 240 V and draw roughly 1.5 to 3 kW, though larger machines may need more.
- Identify an earthed socket within easy reach of the cutting point.
- Plan how the cable will run. Keep it short, keep it dry and keep it off the floor.
- If you have an RCD, test it. If not, discuss adding protection with your electrician.
- Decide what happens if power fails. A small inverter or generator can help, but it must handle the motor's starting load.
Water
- Choose a water source close to the work: a tap, a tank, a drum or large buckets.
- Check that the water is clean, since sediment can clog the rig and shorten bit life.
- Estimate volume. Small jobs need modest amounts, but several large holes call for more.
- Confirm pressure. If your tap is weak, let the contractor know so they can bring a pump.
Slurry and cleanup
Wet cutting creates grey slurry. Plan for sheets, wet vacuums, sponges and a disposal point away from household drains. For slab holes, ask the crew whether they use a collection ring to protect rooms below.
Lighting and ventilation
Dim basements, stairwells and storage rooms are hard places to work. Arrange extra lighting and open windows or doors for airflow.
For a broader look at who normally provides what, see our core cutting preparation guide.
T-3 Days: Plan Machine Access
Even a small rig can be awkward to move. Plan the route from the entrance to the cutting point.
The route
- Entry: Are gates, doors and lifts wide and tall enough? Note any steps or narrow turns.
- Lift rules: In apartment societies, lifts may be restricted for equipment or need advance booking.
- Stairs: If equipment must go upstairs, count the flights and note landings.
- Floor protection: Plan boards or thick sheets for tiled, marble and wooden floors.
The working space
- Leave at least a metre of clear space around the cutting point, and more for wall-saw work.
- Check headroom for ceiling holes. Drill stands need vertical clearance, and false ceilings may need partial removal.
- For terraces and exterior walls, ensure a stable, safe platform or scaffold.
- Note obstructions such as pipes, cables, furniture and fixed cabinets.
Heavy pieces
Cut cores and blocks can be heavy. Decide where they will go and how they will leave the property. For larger openings, plan lifting or lowering equipment.
Parking and unloading
Ask the society or neighbours about parking for the crew's vehicle. In busy markets, check whether loading is permitted at certain hours only.
For an overview of machine and method choices, you can also read our comparison of diamond wall cutting versus traditional breaking.
T-1 Day: Make the Site Ready
The day before is for final checks and clearing.
Clear and protect
- Remove furniture, appliances, curtains, rugs and valuables from both sides of the wall or slab.
- Cover remaining items with plastic sheets.
- Lay floor protection along the path from the entrance to the work area.
- Keep pets and young children away from the area.
Isolate services
- If there is any doubt about wiring or pipes near the cutting line, switch off the relevant circuit or close the valve.
- Confirm that scanning has been done or is planned for the morning.
Confirm marks and approvals
- Recheck the hole markings and photos.
- Make sure society or landlord permission is in place.
- Inform neighbours about the time and expected noise.
Reconfirm the crew
Send a WhatsApp message with the address, contact person, floor, lift details, timing and a link to the marked-hole photos. Ask the contractor to confirm arrival time, equipment list and who is coming.
T-0: The Day of Cutting
A brief routine keeps things smooth.
- Meet the crew and walk them through the work area.
- Confirm the plan by checking each marked point against your list.
- Verify utilities. Test the socket, check the water and arrange cable routing.
- Discuss safety. Point out switches, valves and any hazards.
- Stay reachable. Keep a decision-maker nearby or available by phone.
- Inspect each hole as it is completed for position, diameter and clean edges.
- Check cleanup. Make sure slurry, dust and debris are removed before the crew leaves.
Common Planning Mistakes and How to Avoid Them
| Mistake | How to prevent it |
|---|---|
| Wrong diameter | Ask the plumber or AC technician for exact pipe and sleeve sizes |
| Hole too close to a beam or edge | Review drawings and get engineer advice |
| No earthed socket nearby | Identify and test the socket before the visit |
| Empty water tank | Fill the tank or drum the day before |
| Equipment cannot reach the site | Check lifts, stairs and door widths early |
| Furniture left in the work zone | Clear both sides the day before |
| No permission from society | Get written approval in advance |
| Unclear scope or price | Agree inclusions, extras and timings in writing |
Local Insights: Planning Core Cutting Across Punjab
Different parts of Punjab bring different planning needs.
- Ludhiana and Jalandhar: Commercial and industrial properties often have fixed working hours and heavy traffic. Plan machine access and parking early, and agree shutdowns for live production areas.
- Mohali, Kharar and Zirakpur: Apartment societies commonly require lift booking, approved timings and sometimes security deposits. Add these steps to your T-7 plan.
- Amritsar and Patiala: Older streets can be narrow and buildings may have steep stairs. Check carrying routes, and plan for hand-carried equipment where vehicles cannot reach.
- Bathinda, Moga and Hoshiarpur: Power quality and water availability can vary in outlying areas. Confirm utilities in advance and discuss generators and water supply with the contractor.
- Seasons: In summer, schedule for mornings to avoid heat and peak power demand. During the monsoon, protect extension cables and avoid working on wet terraces.
To find a verified crew near you, visit our core cutting service in Punjab page. You can also explore our wall cutting, slab cutting and door cutting pages, or read our guide to 15 things every homeowner must know before core cutting.
Planning Checklist at a Glance
| Timing | Action | Done |
|---|---|---|
| T-7 | Measure diameter, thickness, position and spacing | ☐ |
| T-7 | Photograph and mark each hole | ☐ |
| T-7 | Check structural risk near beams and columns | ☐ |
| T-5 | Confirm power rating, earthed socket and backup | ☐ |
| T-5 | Arrange water source and slurry plan | ☐ |
| T-3 | Check route, lift, stairs and headroom | ☐ |
| T-3 | Plan parking and handling of cut pieces | ☐ |
| T-1 | Clear and protect the area on both sides | ☐ |
| T-1 | Isolate services and confirm permissions | ☐ |
| T-1 | Send crew details and photos | ☐ |
| T-0 | Walk the site, verify utilities, inspect each hole | ☐ |
Frequently Asked Questions
What measurements do I need before core cutting?
You need the hole diameter, wall or slab thickness, exact position from fixed references, spacing between holes and the clearance on the other side. Photos of marked points help the contractor quote accurately.
What utilities are required for core cutting?
Most jobs need an earthed electrical supply, a steady clean water source and a plan for slurry cleanup. Good lighting and ventilation also help, especially in enclosed areas.
How much space does the machine need?
Allow at least a metre of clear space around the cutting point, and more for wall saws. Check headroom for ceiling holes and make sure the route from the entrance is wide enough for the equipment.
How early should I plan core cutting?
Starting about a week ahead is ideal. It gives you time to measure, take approvals, arrange utilities and confirm access without rushing.
How much does core cutting cost?
Cost depends on diameter, depth, material, reinforcement and access. Use our rate calculator for an estimate, then get a written quote after a site inspection or photo review.
Conclusion: Good Planning Turns a Hard Day Into an Easy One
Core cutting does not have to be stressful. Measure carefully, arrange power and water, plan how the machine will reach the work area, and make the site ready before the crew arrives. With a simple countdown schedule, you remove most of the surprises, protect your property and keep costs under control.
If you are planning core cutting anywhere in Punjab, send us your measurements and photos. We will help you finalise the plan and connect you with a verified contractor.
📞 Call or WhatsApp now: 7009679903
📧 Email: info@corecuttingindia.com
🌐 Website: corecuttingindia.com
🧮 Instant estimate: Core Cutting Rate Calculator